Sony RM-V40A Instrukcja Użytkownika Pobierz pdf (Strona 1)

Setting Up the Remote Commander

Before you can start using the Commander, you must first set it up.

This manual describes everything you need to know to set up the

Commander, including:

•Installing the batteries.

•Presetting the Commander with the codes for your TV, VCR, Cable

box, DBS tuner, and other audio components.

About Presetting the Commander

The Commander is preset at the factory to operate Sony brand

components.

If you’re using the Commander with a Sony component, you won’t

need to preset the Commander before you start using it.

To set up the Commander to use with other (non-Sony)

manufacturers’ components, or to use with a component that is not

preset at the factory, you’ll need to follow the instructions in this

manual to preset the Commander with the correct code number for

your components. (See the supplied “Component Code Numbers”

also.)

Notes

•The Commander can be set up to operate only one component on

each position of the slide switch – unless their code numbers

happen to be the same. For example, you cannot set up the

Commander to operate a Sony TV and a Panasonic TV

simultaneously (because they use different code numbers).

•You may not be able to operate even a Sony brand component with

the factory presetting. In such a case, follow the procedure in

“Setting the Code.”

Installing the Batteries

Slide open the battery compartment and insert two size AA (R6)

batteries (not supplied).

Be sure to line up the + and – on the batteries with the + and – on the

battery compartment.

When to replace the batteries

Under normal conditions, batteries will last up to six months. If the

Commander does not operate properly, the batteries might be worn

out. Replace the batteries with new ones.

Notes

•Replace both batteries with new ones.

•Do not take more than 20 minutes to replace the batteries;

otherwise, your setting of the code numbers will be erased.

Remote Button Descriptions

Operating a TV

Operating a VCR

1 To turn on and off.

2 To change the input mode.

3 To change the channel. For example, to

change to channel 5, press 0 and 5 (or ,

press 5 and ENTER.)

4 To display the on-screen menu (Sony

VCR only).

5 To record, press ” while pressing r.

6 To play.

7 To rewind.

8 To pause.

9 To stop.

!º To switch to VCR operation. Set to the

position on which the VCR is assigned.

(VCR, AV1, AV2/DBS, or CBL)

!¡ To set up the Commander.

!™ To change the channel. For example, to

change to channel 5, press 5 and ENTER.

!£ To fast-forward.

!¢ Channel up: +

Channel down: –

Operating a Cable box

Operating a DBS tuner

1 To turn on and off.

2 To switch the output of the DBS receiver

to the TV. (When you connect a TV

cable or antenna to the receiver, the

output switches between a TV and DBS

program.)

3 To call up the MENU display.

4 To scroll through the Master Guide.

5 To switch to DBS operation. Set to the

position on which the DBS is assigned.

(AV2/DBS, AV1, or CBL)

6 To bring up the Station Index.

7 To change the channel. For example, to

change to channel 5, press 0 and 5 (or

press 5 and ENTER).

8 To change the channel. For example, to

change to channel 5, press 5 and ENTER.

9 To bring up the Master Guide.

0 To select the channel that’s highlighted.

To bring up the Station Index when a

program guide is not displayed.

!¡ Channel up: +

Channel down: –

To page through the guide when a

program guide is displayed.

!™ To tune to the last tuned station.

1 To turn on and off.

2 To set up the Commander

3 To change the channel. For example, to

change to channel 5, press 0 and 5 (or ,

press 5 and ENTER.)

4 To switch to cable box operation. Set to

the position on which the cable box is

assigned. (CBL, AV1, or AV2/DBS)

5 To change the channel. For example, to

change to channel 5, press 5 and ENTER.

6 Channel up: +

Channel down: –

7 To operate JUMP, FLASHBACK or

CHANNEL RETURN function on the TV

depending on the setting of the TV’s

manufacturer.

Notes

• There may be cases you may turn on/off

the cable box by pressing the CH+ or CH–

buttons on the Commander.

• If your cable box can control volume, be

sure to set its volume control to a

medium position. If the volume on the

cable box is turned down completely, you

will not be able to adjust your TV’s

volume with the Commander.

Notes on Batteries

•Do not mix old batteries with new ones or mix different types of

batteries together.

•If the electrolyte inside the battery should leak, wipe the

contaminated area of the battery compartment with a cloth and

replace the old batteries with new ones. To prevent the electrolyte

from leaking, remove the batteries when you plan not to use the

Commander for a long period of time.

Setting the Code

Follow the steps 1 and 2 below for each component you plan to use

with the Commander.

Step 1: Entering the Code Number

1 See the supplied “Component Code Numbers”, and find the code

number in double figures for the desired component.

If more than one code number is listed, use the number that’s

listed first to complete the steps below.

For example, if you’re setting up a Philips’ VCR, you would use

the code number 13.

If your component isn’t listed, see “Searching for the Correct

Code.”

2 Set the slide switch on the Commander

to the position that correspond to the

desired component.

Note

On the AV1, AV2/DBS, and CBL positions, “receiver”, “DBS tuner”,

and “cable box” are assigned respectively at the factory. But you can

also assign other components on these positions. For details, see

“Changing the Component Type on the AV1, AV2/DBS, and CBL

positions.”

3 Press the SET button with a ball-point

pen tip etc., and release it.

4 Enter the component’s code number.

For example, if you’re entering the code

for a Philips’ VCR, you would press and

release 1, then press and release 3.

5 Press and release the ENTER button to

store the code number in the

Commander’s memory.

6 Go to “Step 2: Checking if the Code Number Works” to finish

setting up.

Step 2: Checking if the Code Number Works

1 Power on the component you want to set up.

2 Aim the Remote Commander at the component and press a button

to check if that button works.

For example, press the POWER button to see if it works on your

component .

3 Check that the other buttons of the Commander is operating the

corresponding functions of the component.

If the Commander Doesn’t Seem to Be Working...

•First, try repeating these setup procedures using the other codes

listed for your component (see the supplied “Component Code

Numbers”).

•If – after trying all the codes listed for your component – you still

cannot get the Commander to work properly, try the search

method described in “Searching for the Correct Code.”

Tip

Use the label (supplied) to write down the code numbers of your

components. Then affix the label to the back of the Commander.

Searching for the Correct Code

If you’ve tried all the code numbers listed for your component and

you still cannot get the Commander to work (or if your component is

not listed in the “Component Code Numbers” table), try these steps.

1 Power on the component you want to set up. Insert a tape or disc

if necessary.

2 Set the slide switch on the commander

to the position that corresponds to the

component.

3 Press the SET button with a ball-point

pen tip etc., and release it.

4 Press and release the CH+ button. Then

press and release the POWER button.

5 Repeat step 4 until the correct code number is found.

Each time you press the CH+ button and then the POWER button,

a new code number will be transmitted.

Keep trying until your component operates by receiving the

transmitted signal from the Commander (e.g., the power turns off,

the CH+ function works, playback starts, etc.). Be patient as you

do this; it may take 50 or 60 tries until the correct code number is

located.

6 When the correct code is found, press

and release the ENTER button to store

the code number in the Commander’s

memory.

7 Check that the Commander is operating the other functions of

your component by pressing the corresponding buttons on the

Commander. If they seem to be working properly, you’re done

setting up the Commander.

If the component does not operate properly, repeat steps 1 to 6 and

search for another code. As the searching always starts from 01, it

will stop again at the same code as the last searching. Pass the code

and continue searching until the next code by which the component

operates.

If you still cannot get the Commander to work properly, see

“Troubleshooting.”

Changing the Component Type on the AV1,

AV2/DBS and CBL Positions

At the factory, “receiver” is assigned on the AV1 position, “DBS

tuner” on the AV2/DBS position , and “cable box” on the CBL

position. By completing the following procedure, you can change

this setting so that you can set up any component on these positions.

1 Set the slide switch to the AV1, AV2/DBS

or CBL position.

2 Press the SET button with a ball-point

pen tip etc., and release it.

3 Press and release the p (stop) button.

4 Press and release one of the following

buttons;

1 to assign a VCR

4 to assign a receiver

5 to assign a CD player

6 to assign a tape deck

7 to assign an MD deck or a DAT deck

8 to assign a TV

9 to assign a Cable box

0 to assign a DBS tuner

5 Press and release the ENTER button.

6 Enter the component’s code number by following steps 3 to 6 of

“Entering the Code Number”, or steps 1 to 7 of “Searching for the

Correct Code.”

Controlling the Volume of Video

Components Connected to an Audio

System

The Commander is factory preset based on the assumption that you

hear the sound of your video components from your TV’s speakers,

and that you hear the sound of your audio components from the

loudspeakers connected to your receiver (or amplifier).

Factory Setting:

* If you assign an audio component on the CBL or AV2/DBS position, you can control

the volume of the receiver (or amplifier) on the AV1 position. If you assign video

components on these positions, you can control the volume of the TV.

Thus you can control the volume of your TV or receiver (or

amplifier) while operating a video or audio component without first

having to change the slide switch to TV or AV1 position. For

example, to control the volume for your VCR channels, you don’t

need to change the slide switch to the TV position.

However, if your video components are connected to an audio

system, you probably hear your TV’s or VCR’s sound from the

loudspeakers connected to your receiver ( or amplifier), not from

your TV speakers. In this case, you need to change the factory setting

so that you can control the volume of your video components

without first having to switch to the receiver (or amplifier).

To change the factory setting for the volume control, follow the

procedures below.

Note

This feature is effective only when a receiver or amplifier is set up on

the AV1 position. You cannot control the volume of a receiver (or

amplifier) set up on CBL or AV2/DBS position while operating a

component of another position.

Changing the Factory Setting for the

Volume Control

1 Set the slide switch to the AV1 position.

2 Press the SET button with a ball-point

pen tip, etc. and release it.

3 Press the VOL+ button.

4 Press the ENTER button.

The volume control setting is changed to

“Receiver/amplifier.” You can control

the volume of the receiver (or amplifier)

of the AV1 position while selecting any

component.

Notes

•If you are using more than one receiver (or amplifier) and have set

it on the CBL or AV2/DBS position, from those positions you

cannot control the volume of the receiver (or amplifier) of the AV1

position.

•If you change the setting of the AV1 position to a component other

than a receiver or amplifier, the volume control setting of video

components will return to “TV” even if you have changed the

factory preset volume control. In this case, you will not be able to

control the volume from audio components other than a receiver

or amplifier.

To reset to factory preset volume control

In step 3 above, press VOL – instead.

Operating a Component

1 Make sure that the slide switch is set to

the position that corresponds to your

desired component.

2 Point the Commander directly at the component.

3 Press the button for the function you want to use.

See “Remote Button Descriptions” for complete descriptions of the

buttons on the Commander.

Notes on Using the Remote Commander

Basically, use this Commander in the same way as the Commanders

supplied with your components.

•Using this Commander will not increase the functions of your

components. The functions of the Commander are limited to the

functions of the components themselves. For example, if your TV

does not have a MUTING function, the MUTING button on this

Commander will not function with your TV.

•Some functions of the component may not work with this

Commander.

•If your cable box can control volume, be sure to set its volume

switch to a medium position. If the volume on the cable box is

turned down completely, you will not be able to adjust your TV’s

volume with the Commander.

Position of the slide switch

VCR

CBL*

AV1

AV2/DBS*

Controls the volume of

Receiver (or amplifier)

1 To turn on and off.

2 To change the input mode.

3 To change the channel. For example, to

change to channel 5, press 0 and 5 (or

press 5 and ENTER.)

4 To display the current channel on TV.

5 To call up the MENU display

6 To enter the selection.

7 To move the cursor to the left.

8 To move the cursor downward.

9 Volume up: +

Volume down: –

!º To operate the Picture-in-Picture

function.

Pressing each button while pressing the

PIP button operates as the table below.

!¡ To mute the volume on the TV.

!™ To switch to TV operation. Set to the

position on which the TV is assigned.

(TV, AV1, AV2/DBS, or CBL)

!£ To set up the Commander.

!¢ To operate SLEEP function on the TV.

(Works only for a TV with the SLEEP

function.)

!∞To change the channel. For example, to

change to channel 5, press 5 and ENTER.

!§ To move the cursor upward.

!¶ To move the cursor to the right.

!• Channel up: +

Channel down: –

!ª To operate JUMP, FLASHBACK or

CHANNEL RETURN function on the TV

depending on the setting of the TV’s

manufacturer.

Operating a Receiver

1 To turn on and off.

2 To set up the Commander.

3 To select the input source:

1selects VIDEO 1

2selects VIDEO 2

3selects AUX

4selects TUNER

5selects CD

6selects TAPE 1

7selects TAPE 2

8selects TV

9selects PHONO

(0 switches to another input source by

each pressing).

4 Volume up: +

Volume down: –

5 To mute the volume on a receiver.

6 To switch to Receiver operation. Set to

the position on which the Receiver is

assigned. (AV1, AV2/DBS, or CBL)

7 Presetting frequency up: +,

down: –

Tuning frequency up: +,

down: –

8 To shift band (FM/AM).

Troubleshooting

If you have problems setting up or using the Commander:

•When setting up the Commander, carefully go through the

procedures described in “Setting the Code.” If the code that’s

listed first for your component doesn’t work, try all the codes for

your component - in the order in which they’re listed. If all the

codes fail to work (or if your component is not listed in this

manual), try using the procedures in “Searching for the Correct

Code.”

•Check that you’re aiming the Commander directly at the

component, and that there are no obstructions between the

Commander and the component.

•Make sure the batteries you’re using are not worn out, and that

they’re inserted correctly.

•Check that the slide switch is set to the component you want to

control.

•Check that the component has infrared remote capability. For

example, if your component didn’t come with a remote

commander, it probably isn’t capable of being controlled by a

remote commander.

•If your video components are connected to an audio system, make

sure you’ve set up the Commander as described in “Controlling

the Volume of Video Components Connected to an Audio System.”

•Should any problem persist, reset the Commander to the factory

setting by pressing the POWER, TV/VIDEO and VOL– buttons

simultaneously.

Specifications

Operable distance Approx. 7 m (23 ft) (varies depending of the

component of each manufacturer)

Power requirements Two size AA (R6) batteries (not supplied)

Battery life Approx. 6 months (varies depending on frequency of

use)

Dimensions Approx. 60 × 207 × 41.5 mm (w/h/d)

/2 × 8

/4 × 1

/16 in.)

Mass Approx. 100 g (3.5 oz.) (not including batteries)

Supplied accessory Label (2)

Design and specifications are subject to change without notice.

Operating a CD player, an MD deck or a DAT deck

1 To turn on and off.

2 To set up the Commander.

3 To select the track number. 0 selects

track 10.

To select track numbers above 10, see

the descriptions on the DISP button

below.

4 To select numbers 10 and above.

For example, to select track 15, press

DISP and then press 5.

5 To record, press ” while pressing r/

First release ”, then release r. (MD and

DAT deck only)

6 To pause.

7 To select the previous track.

8 To stop.

9 To switch to CD, MD, or DAT operation.

Set to the position on which the desired

component is assigned. (AV1, AV2/DBS,

or CBL)

0 To play.

!¡ To select next track.

!™ To select next disc. (CD player and MD

deck only)

Operating a tape deck

1 To set up the Commander.

2 To select the tape deck and direction:

1selects Deck A (dual cassette deck

only*).

2selects Deck B (dual cassette deck

only*).

0functions as “ REV button, or switches

play sides.

(The other buttons do not have assigned

functions).

3 To record, press ” while pressing r/

First release ”, then release r.

4 To pause.

5 To rewind.

6 To stop.

7 To switch to tape deck operation. Set to

the position on which the tape deck is

assigned. (AV1, AV2/DBS, or CBL)

8 To play.

9 To fast-forward.

0 To select the tape deck: deck A or deck B

(dual cassette deck only**).

* If your deck’s commander has two sets of

tape operating buttons and has no A/B

button for deck selection, use the numeric

buttons (1 and 2): button 1 selects Deck

A, and button 2 selects Deck B.

**If the deck’s commander has one set of

tape operating buttons, and has an A/B

button for the deck section, use the

RECALL button to select Deck A or B.

English

VCR TV

AV1 CBL

AV2/DBS

SET

ENTER

VCR TV

AV1 CBL

AV2/DBS

SET

ENTER

VCR TV

AV1 CBL

AV2/DBS

SET

POWER

ENTER

POWER

TC/VIDEO

SET

MENU GUIDE

VOL CH

TV/DBS

MUTING

VCR TV

AV1 CBL

AV2/DBS

RECALL

SHIFT

VIDEO 1

SLEEP

DISP ENTER

VIDEO 2

AUX

TUNER

TAPE 1

TAPE 2 TV PHONO

789

∏

‚

PIP

!¢

!∞

!§

!¶

!•

!ª

!™

!£

!º

!¡

POWER

TC/VIDEO

SET

MENU GUIDE

VOL CH

TV/DBS

MUTING

VCR TV

AV1 CBL

AV2/DBS

RECALL

SHIFT

VIDEO 1

SLEEP

DISP ENTER

VIDEO 2

AUX

TUNER

TAPE 1

TAPE 2 TV PHONO

789

∏

‚

PIP

!¢

!™

!£

!º

!¡

POWER

TC/VIDEO

SET

MENU GUIDE

VOL CH

TV/DBS

MUTING

VCR TV

AV1 CBL

AV2/DBS

RECALL

SHIFT

VIDEO 1

SLEEP

DISP ENTER

VIDEO 2

AUX

TUNER

TAPE 1

TAPE 2 TV PHONO

789

∏

‚

PIP

POWER

TC/VIDEO

SET

MENU GUIDE

VOL CH

TV/DBS

MUTING

VCR TV

AV1 CBL

AV2/DBS

RECALL

SHIFT

VIDEO 1

SLEEP

DISP ENTER

VIDEO 2

AUX

TUNER

TAPE 1

TAPE 2 TV PHONO

789

∏

‚

PIP

!º

!¡

!™

POWER

TC/VIDEO

SET

MENU GUIDE

VOL CH

TV/DBS

MUTING

VCR TV

AV1 CBL

AV2/DBS

RECALL

SHIFT

VIDEO 1

SLEEP

DISP ENTER

VIDEO 2

AUX

TUNER

TAPE 1

TAPE 2 TV PHONO

789

∏

‚

PIP

POWER

TC/VIDEO

SET

MENU GUIDE

VOL CH

TV/DBS

MUTING

VCR TV

AV1 CBL

AV2/DBS

RECALL

SHIFT

VIDEO 1

SLEEP

DISP ENTER

VIDEO 2

AUX

TUNER

TAPE 1

TAPE 2 TV PHONO

789

∏

‚

PIP

!º

!¡

!™

POWER

TC/VIDEO

SET

MENU GUIDE

VOL CH

TV/DBS

MUTING

VCR TV

AV1 CBL

AV2/DBS

RECALL

SHIFT

VIDEO 1

SLEEP

DISP ENTER

VIDEO 2

AUX

TUNER

TAPE 1

TAPE 2 TV PHONO

789

∏

‚

PIP

!º

3-864-374-22(1)

Remote Commander

RM-V40A

Operating Instructions

Mode d’emploi (au verso)

VCR TV

AV1 CBL

AV2/DBS

VIDEO 1

TUNER

TAPE 1

TAPE 2 TV PHONO

789

VCR TV

AV1 CBL

AV2/DBS

VOL

SET

ENTER

Your Code Number

Component that can be preset

VCR

Position

VCR

CBL

AV1

AV2/DBS

Factory setting

Sony TV

Sony VHS VCR

—

Sony Receiver

Sony DBS tuner

Cable box/DBS tuner/

Receiver/CD player/Tape deck/

MD deck/DAT deck/TV/VCR

PIP operations

Press To

PIP and DISP Turn on/off the “window” picture.*

PIP and ENTER Turn off the “window” picture.

PIP and CH+ or CH– Change the TV channel in the “window” picture.

PIP and TV/VIDEO Change the input mode of the “window” picture.

PIP and 1 Move the location of the “window” picture.

PIP and 2 Swap the “main” picture and the “window” picture.

PIP and 3 Freeze the “window” picture.

* If the “window” picture does not turn off this way, try pressing ENTER while

pressing PIP.

1 2

TAPE 2 TV PHONO 1

Podsumowanie treści

Strona 1 - TAPE 2 TV PHONO

Setting Up the Remote CommanderBefore you can start using the Commander, you must first set it up.This manual describes everything you need to know to

Strona 2

Préréglage de la télécommandeAvant de pouvoir utiliser la télécommande, vous devez la prérégler.Ce manuel décrit tout ce que vous devez savoir pour pr