Sony RM-VL700S Instrukcja Użytkownika Strona 1

3-232-145-12 (1)Integrated RemoteCommanderOperating Instructions© 2001 Sony CorporationRM-VL700

10Setting the Code for non-SonyPreset Audio and VisualComponents (continued)Checking if the codenumber works1 Power on the componentwith its power swi

11Setting a componentcode by the SearchfunctionYou can find a code numberavailable for a component thatdoesn’t have one in the supplied“Component Code

124 Press ENT.The Component button turnsoff.If the Component Select buttonflashes five times before turningoff, it means that the setup isincomplete.

13To control the volumePress VOL +/– to control thevolume. Press MUTING to mutethe sound. When you select avisual component, the TV’svolume will be co

14Notes on operating yourcomponentsAbout the input select of a TVEach time TV/VIDEO is pressed,the input is changed in order. It isalso possible to se

15about 2 – 4 inches(5 – 10 cm) awayRemote control foryour componentRM-VL700ContinuedProgramming signalsof another remotecontrol — LearningFunctionTo

16Programming signals of anotherremote control— Learning Function (continued)3 Press the Component Selectbutton for the componentwhose signals are to

175 Press and hold the buttonon the other remote control,until both the SET indicatorand the Component Selectbutton lights up again.During data transf

18Programming signals of anotherremote control— Learning Function (continued)When you “teach” signals toVOL +/– or MUTING•If you used the Learningfunc

192 Press and hold theComponent Select buttonfor the component whosesignals are to be “learned”for over 3 seconds.SET and all other ComponentSelect bu

2For the customers in the U.S.A.WARNINGThis equipment has been tested and found to comply with the limits for aClass B digital device, pursuant to Par

20Programming signals of anotherremote control— Learning Function (continued)3 Press and hold the buttonon the other remote control,until the SET indi

21ContinuedChanging or erasing thefunction of a “learned”buttonTo change the “learned” function,clear it first and perform Learningagain.To clear the

22Programming signals of anotherremote control— Learning Function (continued)To clear all function signals“learned” for a specificComponent Select but

23Notes on programming thesignals for an air-conditionerAbout seasonal adjustmentsIf you change the settings of theair-conditioner for the season, you

24Component SelectbuttonTVVCRCBL/SATDVDAMPControls the volume ofTVTVTVTVamplifierAdvanced FeaturesControlling the Volumeof Visual ComponentsConnected

25To set only the audiocomponents’ volume controlsto AMPPress VOL– while holdingMUTING pressed.Only AMP lights up when youpress these buttons, and the

26Adding an ExtraFunction to theComponent SelectButtonsProgramming the Power-OnCommand of the SelectedComponent just by pressingthat Component Selectb

27Assigning OtherComponents to theComponent SelectButtonsYou can assign anothercomponent to any of theComponent Select buttons notbeing used.Notes• On

28To reset a Component Selectbutton to its original settingPerform the setting of the originalcomponent following theprocedure on page 27. Notehowever

292 Press and hold for over 3seconds the desiredComponent Select button towhich you want to copy asetting from anothercomponent.While holding down thi

3FeaturesThe RM-VL700 Remote Commander provides centralized control of allyour AV components from a single remote commander and saves thetrouble of op

30Using Other FunctionsLocking the Controls— Hold FunctionTo prevent accidental operation,you can lock all the buttons withthe Hold function.1 While h

31Erasing all settings— To reset theCommander to itsfactory settingsYou can erase all remote controlsignals programmed by the“learned“ function to res

32SpecificationsOperating distanceApprox. 32.8 ft. (10 m) (variesdepending on components ofdifferent manufacturers)Power requirementsTwo size AA (R6)

33TroubleshootingIf you have problems setting up or using the Remote Commander, firstcheck the batteries (page 6), then check the items below.Remedy•

34SymptomThe SET indicator falshesfive times during theLearning procedure.A Component Selectbutton flashes five timesduring setting.The SET indicator

35KEY DISPLAY0POWER3qd1 – 9, 0, ENT1TV/VIDEO2DISPLAYqsSLEEPqaGUIDE(PIP OFF)7MENUTVFUNCTIONTo turn on and off.To change the channel.For example, to cha

36Table of Preset Functions(continued)KEY DISPLAY0POWER3qd1 – 9, 0, ENT2DISPLAY1TV/VIDEO(ANT/SW)qsSLEEP(INPUTSELECT)7MENU6f6F6G6gqfOK5m5N5M5REC z5x5Xq

37KEY DISPLAY0POWER31 – 9, 04PIP(+10)qdENT1TV/VIDEO(AUDIO)2DISPLAYqaGUIDE(CLEAR)qhRECALL(RETURN)5REC z(TITLE)qsSLEEP(SUBTITLE)7MENU(DVDMENU)6f6F6G6gqf

38KEY DISPLAY0POWER5m5N4PIP (n)5M5REC z5x5XqhRECALL(A/B)7MENU (z)6f (N)6F (x)6G (M)6g (m)qdENT (n)qfOK (X)DECKFUNCTIONTo turn on and off.To rewind.To

39KEY DISPLAY0POWER31323334353637383930qaGUIDE(INPUT)qhRECALL(SHIFT)qgCH+/–8VOL +/–9MUTINGAMPFUNCTIONTo turn on and off.To select the inputsource: VID

4Table of ContentsGetting StartedInstalling the Batteries ... 6When to r

40IndexA, BBatteries 6C, DChanging 21CH (CHANNEL) button 11Clearing/Changinglearned signal 21, 22Power-On command 26Code number 8, 11Component S

5AppendixTable of Preset Functions ... 35TV ...

6Getting StartedInstalling theBatteriesSlide open the batterycompartment lid and insert twosize AA(R6) batteries (notsupplied). Be sure to match up th

7Location of Controls1 SET indicator2 SET button3 Component Select buttonsLight or flash during operation.4 TV/VIDEO button5 DISPLAY button6 Number bu

82 Press SET.All Component Select buttonsflash.Example: To set up a Philips’ TV1 See the tables in thesupplied “ComponentCode Numbers”, and findthe th

93 Press the Component Selectbutton for the desiredcomponent.The selected Componentbutton lights up, and all otherbuttons turn off.4 Press the Number